Webinar: Make your content AI-readyWatch replay now

V2000-c Rfid Access Control User Manual Guide

: Relay Common (COM) – Connects to lock power supply control

Press and hold down the # key (or the reset button located on the back PCB, depending on production batch). the device while continuing to hold the key. Release the key after hearing a series of short beeps.

Normally Closed (NC) – Connects to Fail-Safe locks (unlocks when power is cut, like magnetic locks).

| Feature | Specification | | :--- | :--- | | Operating Voltage | DC 12V (±2V) | | Standby Current | < 35mA | | Open Current | < 150mA | | Card Type | EM (125KHz) / Mifare (13.56MHz) | | User Capacity | 1,000 cards / 1,000 PINs | | Output Relay | Dry contact (NO/NC/COM), max 2A/30VDC | | Working Temp | -20°C to +60°C | | IP Rating | IP65 (weatherproof) | V2000-c Rfid Access Control User Manual

While minor factory variations exist, the standard V2000-C pigtail harness typically follows this color-coded configuration: Wire Color Label / Function Connection Destination Positive terminal of 12V DC power supply Black GND (Ground) Negative terminal of power supply Green NO (Normally Open)

The V2000-c supports two adding methods: by card swipe or by manual ID entry.

Normally Open (NO) – Connects to Fail-Secure locks (unlocks when energized). White: Common (COM) – Relay common terminal. : Relay Common (COM) – Connects to lock

The V2000-C tracks users via numbered from 1 to 2000 . Assigning specific User IDs is highly recommended so you can delete lost cards without needing the physical card in hand. Adding Users (Card or Fob Only) Enter programming mode. Press 1 . Enter a unique User ID (e.g., 0001 to 2000 ) followed by # .

This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later.

Incorrect PIN, unregistered card, or programming syntax error. Alarm Triggered Tamper sensor activated or door forced open. Common Troubleshooting Scenarios Normally Closed (NC) – Connects to Fail-Safe locks

: Relay Normally Closed (NC) – Connects to Fail-Safe locks (Magnetic Locks) YELLOW : Open Button (PUSH) – Connects to the exit button

Note: Factory default is 5 seconds. Set to 0 for a toggle switch action. 4. User Management: Adding and Deleting Users

: Relay Common (COM) – Connects to lock power supply control

Press and hold down the # key (or the reset button located on the back PCB, depending on production batch). the device while continuing to hold the key. Release the key after hearing a series of short beeps.

Normally Closed (NC) – Connects to Fail-Safe locks (unlocks when power is cut, like magnetic locks).

| Feature | Specification | | :--- | :--- | | Operating Voltage | DC 12V (±2V) | | Standby Current | < 35mA | | Open Current | < 150mA | | Card Type | EM (125KHz) / Mifare (13.56MHz) | | User Capacity | 1,000 cards / 1,000 PINs | | Output Relay | Dry contact (NO/NC/COM), max 2A/30VDC | | Working Temp | -20°C to +60°C | | IP Rating | IP65 (weatherproof) |

While minor factory variations exist, the standard V2000-C pigtail harness typically follows this color-coded configuration: Wire Color Label / Function Connection Destination Positive terminal of 12V DC power supply Black GND (Ground) Negative terminal of power supply Green NO (Normally Open)

The V2000-c supports two adding methods: by card swipe or by manual ID entry.

Normally Open (NO) – Connects to Fail-Secure locks (unlocks when energized). White: Common (COM) – Relay common terminal.

The V2000-C tracks users via numbered from 1 to 2000 . Assigning specific User IDs is highly recommended so you can delete lost cards without needing the physical card in hand. Adding Users (Card or Fob Only) Enter programming mode. Press 1 . Enter a unique User ID (e.g., 0001 to 2000 ) followed by # .

This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later.

Incorrect PIN, unregistered card, or programming syntax error. Alarm Triggered Tamper sensor activated or door forced open. Common Troubleshooting Scenarios

: Relay Normally Closed (NC) – Connects to Fail-Safe locks (Magnetic Locks) YELLOW : Open Button (PUSH) – Connects to the exit button

Note: Factory default is 5 seconds. Set to 0 for a toggle switch action. 4. User Management: Adding and Deleting Users